|
BT88
SERIES
|
|
For
door openings up to 8' wide x 8' high with level or
incline driveways
|
|
INFLATABLE
DOCK SEALS
|
 |
|
|
|
Savings |
|
|
|
Flexible
material forms a tight gasket between the truck and
your building, reducing loss of heated or conditioned
building
air. |
|
|
|
Construction |
|
|
|
Rugged
vinyl coated nylon fabric is mounted to a sturdy 3/4"
exterior grade plywood backboard with heavy galvanized
steel
channel hardware. |
|
|
|
Protection |
|
|
|
Tight
seal can reduce product damage in bad weather and
decrease the losses resulting from pilferage. |
|
|
|
Durability |
|
|
|
Switch
operated inflatable seals may be left retracted against
the building in good weather, reducing wear on the seal. |
|
|
|
Safety |
|
|
|
Seals
are inflated by a low pressure blower, providing a tight
seal without exerting damaging pressure on your building
or
endangering your personnel. |
|
|
|
Versatility |
|
|
| Bondors's
Model BT88 |
|
|
|
|
Unique
design, with our factory mounted back board, allows
our seal to be adapted to a wide variety of truck and
building
conditions. |
|
|
Bondor
Inflatable Dock Seals are of a one piece unitized
construction shipped ready for quick and simple installation.
The seal fits flush around an 8' x 8' door opening,
and the
Bondor seal is designed to easily frame down oversize
doors where necessary. The nominal inside opening when
inflated is 7'4" x 7'10" high. For serving
trucks of varying
heights, a weighted drop curtain may be furnished adding
greater flexibility to the range of truck sizes to be
sealed.
Standard projection is 20", inflation time is 10
seconds.
30" projection models are ideal for edge of dock
(EOD)
levelers. Material is 22 ounce vinyl coated nylon. Each
dock seal includes a standard blower with a 1/4 h.p.,
115
volt, single phase shaded pole motor with thermal overload
protection. A galvanized weathershield is provided if
blower is to be externally mounted. For interior mounted
blower units, appropriate elbows are provided as required.
The blower unit carries a one year replacement guarantee.
Electric control switch by others. |
|
|
|
|
Simplicity |
|
|
|
Patented
one piece "unitized" construction allows for
compact
shipping and easy installation. |
|
|
|
Visibility |
|
|
|
Truck
seals have a 4" wide contrasting guide stripe sewn
on. |
|
|
|
Projection |
|
|
|
Standard
20" truck seal projection will seal trucks with
rear
extensions up to 12" on a standard dock with 4"
bumpers. |
|
|
|
Appearance |
|
|
|
Inflatable
seals are provided with elastic shock cords to
eliminate sagging of the deflated material and retract
the seal
neatly against the building. |
|
|
|
|
|
 |
|
 |
|
|
|
|
|
|
| REASONS
FOR CHOOSING BT-88 STYLE INFLATABLE LOADING DOOR DOCK
SEALS |
|
|
|
*
Low pressure exerted on to building reducing possible
damage to building.
* Low pressure exerted onto rear of truck reducing
risk of puncture by trucks.
* Quick inflation, can be interlocked to operate
with overhead door or dock leveler.
* Additional projection can span large gaps between
building and truck.
* Inflated seal can be compressed to within 2"
of building eliminating taper required by foam seals
when applied to
buildings with declining driveway.
* Durable cover fabric (22 oz.- same as a form
dock seal)
* Distinctive appearance. |
|
|
|
 |
|
 |
|
|
|
|
Shown
on Greenhouse - Tight seal with minimal pressure on
building.
|
|
|
|
BT88
Series Inflatable Truck Dock Seals
|
|
|
|
For
Door openings up to 8' wide x 8' high with level or
incline driveways
|
|
|
|
TO
ORDER A SERIES BT88 INFLATABLE TRUCK DOCK SEAL
|
|
|
| 1.
|
Select
the desired dock seal projection from Price Table A
below. |
|
|
| 2. |
Unless
otherwise indicated, the dock seal will be provided
with the standard blower location #1. |
|
|
| 3. |
Select
the desired model number from the price table such as
BT-88/P20/ and add the actual dock door opening size
to
complete the model number. Example: BT-88/P20/8'W x
8'H. This model would specify a BT-88 dock seal with
a 20"
projection for a door opening 8'W x 8'H. |
|
|
| 4. |
Remember
to order 2 dock bumpers per seal from our bumpers section
if they are not existing. Seal should project 6-8"
beyond bumpers. |
|
|
| 5. |
Price
includes all necessary mounting brackets and hardware
except building fasteners. |
|
|
| 6. |
We
invite you to let our engineers review your dock seal
application. Complete the truck dock dimension sheet
on our
contact page and we will confirm your dock seal selection. |
|
|
|
| TABLE
A: BT-88 INFLATABLE DOCK SEAL |
|
|
Projection (inches) Z
|
Standard Backboard
Size Provided |
Use |
Model No. Add |
Price |
|
20 |
6" wide |
Standard |
BT-88/P20/--Wx--H |
$920 |
|
24 |
6" wide |
For extra projection |
BT-88/P24/--Wx--H |
$997 |
|
30 |
12" wide |
Recommended for EOD levelers |
BT-88/P30/--Wx--H |
$1121 |
|
|
|
|
|
|
|
 |
|
 |
|
|
|
|
Easy
Installation
|
|
|
Unitized
Construction
|
|
|
|
|
|
|
|
| ARCHITECTURAL
SPECIFICATIONS - MODEL BT-88 |
|
Truck
dock seals shall be Bondor Inflatable Dock Seals as
manufactured by the Bondor Division of FS Industries,
Providence, Rhode Island. Dock Seals to fit a door opening
______ wide x ______ high. Standard projection is 20". |
|
| Construction: |
|
Units
to be of a one piece unitized construction delivered
completely assembled on 3/4" exterior grade plywood
to be
opened up by means of hinged sections into a 3-sided
unit ready for immediate installation. To Include shock
cords to
eliminate sag of deflated unit. No velcro fastener,
separate sleeves, ducts, etc., to fit one section to
another. |
|
| Side
Members: |
|
Bottoms
have slight upward taper form rear to front to eliminate
sag in front of dock bumpers to prevent pinching. Bottoms
of
side members to contain grommets to allow for breathing
and drainage of moisture in the event of condensation. |
|
| Cover
Material: |
|
| 22
ounce vinyl coated nylon with a 4" contrasting
guide stripe which is to be rolled into the coating,
not painted or sewn on. |
|
| Colors: |
|
| Black
with yellow guide stripe; green with yellow guide stripe;
others available upon request. |
|
| Blower: |
|
1/4
h.p. 115 volts single phase shaded pole motor with thermal
overload, complete with mounting brackets and galvanized
weathershield for exterior mounting. |
|
