LOADING DOCK LIGHTS
			DOCK LIGHTING SYSTEM
STOP & GO LIGHT					LOADING DOCK GUIDE LIGHT
MODEL #SG-10
					MODEL #DGL
	The DockMaster Dock Lighting Control Console is designed to control lighting devices for two adjacent loading docks.

STOP & GO LIGHTS		LOADING DOCK GUIDE LIGHTS
Loading Dock Stop & Go Light is a safety signaling device that can help alert truck drivers and loading dock personnel to the safety status of docked or docking trucks		The Loading Dock Guide Light provides added safety at industrial docks by improving a driver's depth perception when backing into an open dock mouth. When installed below the dock bumpers (and wider than the mirrors of a typical cab's mirrors) the Dock Guide Light focuses light directly onto the face of the dock and dock bumpers. It provides an ideal focal point for drivers and greatly reduces the risk of "overrunning" a dock. Dock Guide Lights can vastly reduce damage and injuries due to trucks backing in too far or too quickly.
As a truck is being directed to an individual loading dock, the Stop & Go Light is switched to flash green. The truck is cleared to back into the dock. When the trailer reaches the dock and is safely locked in place, a signal can be sent to the Stop & Go Light to change the flashing green light outside to flashing red. This tells the driver he is safely docked and is not cleared to move his trailer.
		The Dock guide Light includes adjustable reflectors. When installed, these reflectors produce a focused light pattern that illuminates the dock surface exactly where needed, providing a sharp visual cutoff that assists a driver in lining up a trailer squarely with a dock. (See illustration below)
As an additional safety feature, a second Stop & Go Light can be wired inside the loading area. When the outside light flashes red to let drivers know they are safely docked, the inside light flashes green to indicate that it is safe to begin loading or unloading. The Stop & Go Light can be controlled independently or with the Control Console (see below).
A simple, reliable and cost-effective warning system     that reduces the risk of accidents around the loading     dock.

Safety yellow polypropylene housing will not rust, pit,     dent or corrode like similar metal units.		The Dock Guide Light is constructed of high impact  polycarbonate with ribbed reinforcing. In addition, it is less deep than dock bumpers, reducing the danger of it being struck and damaged by a truck.
Shallow depth of unit (less than most dock bumpers)     reduces risk of damage to Stop & Go Light
Standard automotive bulbs are long-lasting,     inexpensive and easy to replace		The Dock Guide Light operated on 12 volts AC/DC and can be controlled with the Control Console (see below) or any other independent source of low voltage via transformer, etc. Standard automotive replacement bulbs are long-lasting, inexpensive and easy to replace.
Mounting holes line up with most mortar spacings
Compatible with any type of loading dock
Integral eyebrow-type sun visors provide extended     visibility
Unmistakably clear red and green lights provide     immediate and recognizable direction to drivers and     loading dock staff, reducing the risk of operator     confusion and/or error
Establishes a clear line of communication between     drivers and dock personnel

DOCKMASTER® DOCK LIGHTING CONTROL CONSOLE

The DockMaster Dock Lighting Control Console is designed to control lighting devices for two adjacent loading docks from a centralized location inside the dock. One control console can be wired to control two Dock Loading Lights, two or four Stop & Go Lights and two pairs of Guide Lights.		3-position switch on each side flashes the Stop & Go Lights for each respective dock. The innermost switches control the Guide Lights and may be programmed to stay on or to turn off after a preset time. They are independently programmable from 5 to 30 minutes.
		Selecting this self-timer option conserves energy usage and prolongs bulb life. At full load, the Control Console is rated to draw no more than 750 watts to service two docks. Two Control Consoles servicing four docks can be powered by a single 15 amp circuit.
A master switch controls power to all dock lighting equipment and a circuit breaker protects each console against overload.
The Control Console provides equal control for a left and right array of lighting equipment. The outermost 3-position switch on each side flashes the Stop & Go Lights for each respective dock. The innermost switches control the Guide Lights, and may be programmed to stay on, or the turn off after a preset time. They are independently programmable from 5 to 30 minutes.

PRICING FOR DOCK STOP AND GO COMMUNICATIONS LIGHTS

Part No. Description Price SG10-12RG Stop & Go Light, 12 Volt DC-UL/cUL Listed $94.35 SG10-24RG Stop & Go Light, 24 Volt DC-UL/cUL Listed $94.35 SG10-115RG Stop & Go Light, 115 Volt AC-UL/cUL Listed $94.35 SG20-12RG Stop & Go Light with On-Off-On Toggle Switch & Solid State Flasher, 12 Volt DC-UL/cUL Listed $133.20 SG20-24RG Stop & Go Light with On-Off-On Toggle Switch & Solid State Flasher, 24 Volt DC-UL/cUL Listed $133.20 SG20-115RG Stop & Go Light with On-Off-On Toggle Switch & Solid State Flasher, 115 Volt AC-UL/cUL Listed $133.20 SG30-12RG Indoor/Outdoor Set Consisting of (1) SG10-12RG & (1) SG20-12RG-12 Volt DC-UL/cUL Listed $214.23 SG30-24RG Indoor/Outdoor Set Consisting of (1) SG10-24RG & (1) SG20-12RG-24 Volt DC-UL/cUL Listed $214.23 SG30-115RG Indoor/Outdoor Set Consisting of (1) SG10-115RG & (1) SG20-12RG-115 Volt AC-UL/cUL Listed $214.23

For all SG Lights specify required voltage (12, 24 DC and 115 AC)

PRICING FOR LOADING DOCK GUIDE LIGHTS COMMUNICATIONS SYSTEMS

Part No. Description Price DGL Dock Guide Light (12 volt) $35.52 DM-1 Master Control Console & Power Sup $133.20 DM-2 Power Supply for up to 4 DGL units $66.60 DGL-101 Dock Master 2 (Four DGL's + DM-2) $155.40 DGL-202 Dock Master 3 (Two DGL's +DM-2) $125.43