Dock Bumper, Dock Bumpers, Laminated Rubber Bumpers

Laminated Rubber Dock Bumpers

				Features

					Tough plies of truck tire material virtually eliminates chipping or abrasion, unlike molded rubber, extruded rubber, or wood plank bumpers.
					Attractive deep black color enhances a neat, professional architectural look. Manufactured under pressure exceeding 1,500 lbs. to absorb over 80% of impact force. Anchor bolts are protected by at least 3" of rubber to prevent damage.

				Uses / Applications

					Available in two models: bumpers with angles for most applications -- equipped with 1/4" steel angles on both ends; and bumpers with flat plate for use with dock levelers -- optional 1/4" flat steel plate for one or both ends.


					Have unlimited applications in factories, warehouses and docks.
					Vehicle impact protection for loading docks.
					Projecting above low docks.
					Rub rails at the sides of truck wells.
					Wall bumpers to protect against fork lift trucks.
					Special construction features to accommodate unusual anchoring conditions.


Benefits
	Provides maximum protection against vehicle damage to docks, buildings and cargo.	Constructed to last and provide years of protection.
		Constructed to last and provide years of protection.
		Anchored through thick steel angles to provide stability and shape retention.

	Absorbs over 80% of truck umpact and shock to protect dock and building.
		Performs on any truck dock under any weather condition or prolonged exposure.

	Leading bumper sold in the industry today.
		Maintenance free. 5 year warranty.

	Standard sizes shipped within 24 hours.



	Eliminates costly repairs from severe shock to docks.
	Eliminates costly repairs from severe shock to docks.


Material/Thickness
	Fabric reinforced rubber pads cut from selected recycled truck tires. Rubber pads laminated between structural steel angles and secured with 3/4" steel tie rods.	Rubber pads 4-1/2" or 6" thick.
		Rubber pads 4-1/2" or 6" thick.




Installation

	Structural mounting angles permit welded installations or provide bolting through steel.


Specifications
	Furnish and install rubber dock bumpers. Resilient rubber material of bumpers shall be rubberized-fabric truck tires cut to uniform size pads and punched to receive 3/4" supporting rods.	The anchor leg of angle extends a minimum of 3" beyond the rubber surface at either end and contains two or three 13/16" anchor bolt holes as required. (Anchor bolts are supplied separately)


	All bumpers must be 4-1/2" or 6" thick (projection from dock), and closed with two 1/4" structural angles under approximately 1,500 lbs. of pressure.	Black finish.
		Black finish.

		Galvanized exposed metal or all metal available upon request, surcharges apply.

Laminated Rubber Dock Bumpers

B4506 Series B4510 Series B610 Series	*B4512 Series*	B4520 Series B620 Series	B4524 Series B624 Series
		B4520 Series B620 Series	B4524 Series B624 Series

To order Laminated Rubber Bumpers:

1.	Select your required bumper thickness (projection - dimension A) from price table A below, as well as bumper height (dimension B) and bumper length (dimension C ). For level driveways, a 4 1/2" projection is usually adequate. Note: - If you have an inclined driveway and need assistance selecting the necessary dock bumper projection, scroll down to the incline driveway chart below price table B.

2.	We invite you to let our engineers review your dock bumper application. Complete the dock seal dimension sheet on our contact page and we will confirm your dock bumper selection.

Table A: Laminated Rubber Bumper Pricing

Model #	Projection x Height x Bolt Hole Centers (Length) (A x B x C) Size	D Vertical Bolt Hole Centers	E Rubber Length	F Overall Length	Wt. Lbs.	Price F.O.B.Ohio Factory	Price F.O.B. Providence Warehouse
4 1/2" Thick Series
B4506-14	4-1/2" x 6" x 14"	3"	10"	16"	18	$44.63	$56.03
B4506-24	4-1/2" x 6" x 24"	3"	20"	26"	28	$65.59	$76.99
B4506-36	4-1/2 x 6" x 36"	3"	32"	38"	42	$95.24	$106.64
B4510-12	4-1/2 x 10" x 12"	6"	8"	14"	25	$53.65	$68.15
B4510-14	4-1/2" x 10" x 14"	6"	10"	16"	26	$60.92	$75.42
B4510-18	4-1/2" x 10" x 18"	6"	14"	20"	34	$74.28	$88.78
B4510-24	4-1/2" x 10" x 24"	6"	20"	26"	45	$95.24	$109.74
B4510-36	4-1/2" x 10" x 36"	6"	32"	38"	66	$142.59	$157.09
B4512-12	4-1/2 x 12" x 12"	4"	8"	14"	31	$65.38	$84.48
B4512-14	4-1/2" x 12" x 14"	4"	10"	16"	32	$74.28	$93.38
B4512-18	4-1/2" x 12" x 18"	4"	14"	20"	41	$99.48	$118.58
B4512-24	4-1/2" x 12" x 24"	4"	20"	26"	56	$117.29	$136.39
B4512-36	4-1/2" x 12" x 36"	4"	32"	38"	82	$175.28	$194.38
B4520-11	4-1/2" x 20" x 11"	6"	7"	13"	42	$89.05	$111.75
B4524-11	4-1/2" x 24" x 11"	4"	7"	13"	51	$109.79	$137.69
B4536-11	4-1/2" x 36" x 11"	4"	7"	13"	85	$153.99	$191.19
Model #	Projection x Height x Bolt Hole Centers (Length) (A x B x C) Size	D Vertical Bolt Hole Centers	E Rubber Length	F Overall Length	Wt. Lbs.	Price F.O.B.Ohio Factory	Price F.O.B. Providence Warehouse
6" Thick Series
B610-12	6" x 10" x 12"	6"	8"	14"	29	$72.87	$89.37
B610-14	6" x 10" x 14"	6"	10"	16"	33	$80.15	$96.65
B610-18	6" x 10" x 18"	6"	14"	20"	43	$97.85	$114.35
B610-24	6" x 10" x 24"	6"	20"	26"	58	$124.67	$141.17
B610-36	6" x 10" x 36"	6"	32"	38"	84	$184.08	$200.58
B612-12	6" x 12" x 12"	4"	8"	14"	34	$89.05	$110.75
B612-14	6" x 12" x 14"	4"	10"	16"	41	$95.13	$116.83
B612-18	6" x 12" x 18"	4"	14"	20"	51	$118.92	$140.62
B612-24	6" x 12" x 24"	4"	20"	26"	69	$154.54	$176.24
B612-36	6" x 12" x 36"	4"	32"	38"	105	$254.12	$275.82
B620-11	6" x 20" x 11"	6"	7"	13"	52	$124.78	$153.68
B624-11	6" x 24" x 11"	4"	7"	13"	63	$148.56	$183.66
B636-11	6" x 36" x 11"	4"	7"	13"	100	$195.48	$247.08

Note: 1/4" Flat plates may be substituted for one or both angles. Overlap angles are available for 5% upcharge.

Extra-Thick Laminated Rubber Dock Bumpers


		Uses / Applications
			Where greater "stand out" distance from dock sills is required due to steep ramps, canopied docks, overhangs or other architectural features.

		Features
			Consists of tough plies of truck tire fabric which virtually eliminates chipping or abrasion.

		Benefits
			Maintenance free, weather resistant.
			Prevents damage to trucks, loading docks and buildings by providing greater standout distance from dock sills on steep ramps.

			Protects dock seals from over-compression.

				Special Notes
					Refer to stand-out distance planner to choose proper thickness for incline docks.
					Extra-Thick bumpers are not warrantied due to specialty applications where they are used.

B920 Series B10520 Series B1220 Series	B910 Series B10510 Series B1210 Series


Material/Thickness
Material/Thickness		Installation
	Uniform size, fabric reinforced rubber pads cut from selected recycled truck tires in 9", 10-1/2", and 12" projections.	Installation
			Structural mounting angles permit welded installations or provide bolting through steel (as opposed to bolting through rubber).


Specifications

	Furnish and install extra-thick rubber dock bumpers. Resilient rubber material of bumpers shall be rubberized truck tires cut to uniform size pads, in stand-out thicknesses of 9", 10-1/2" or 12", punched to receive 3/4" steel tie rods.	Anchor leg of angle extends a minimum of 3" beyond the rubber surface at either end and contains two or three 13/16" anchor bolt holes as required. (Anchor bolts are supplied separately)

		Finish for exposed metal parts is either chrome aluminum lead-free enamel, or hot-dipped galvanized.

	All bumpers are closed with two 1/4" steel formed angles under approximately 1,500 lbs. of pressure. 1/4" flat plates may be substituted for one or both angles.

Table B: Extra-Thick Laminated Rubber Bumper Pricing

Model #	Projection x Height x Bolt Hole Centers (Length) (A x B x C) Size	D Vertical Bolt Hole Centers	E Rubber Length	F Overall Length	Wt. Lbs.	Price F.O.B. Ohio Factory	Price F.O.B. Providence Warehouse
B-910 Series - 9" Thickness
B910-14	9" x 10" x 14"	6"	10"	16"	63	$173.98	$196.68
B910-24	9" x 10" x 24"	6"	20"	26"	98	$237.40	$260.10
B910-36-A3*	9" x 10" x 36"	6"	32"	38"	152	$341.00	$375.10
B920-11	9" x 20" x 11"	6"	7"	13"	103	$313.85	$359.25
B-10510 Series - 10 1/2" Thickness
B10510-14	10-1/2" x 10" x 14"	6"	10"	16"	71	$223.50	$249.30
B10510-24	10-1/2" x 10" x 24"	6"	20"	26"	109	$288.44	$314.24
B10510-36-A3*	10-1/2" x 10" x 36"	6"	32"	38"	167	$398.13	$439.93
B10520-11	10-1/2" x 20" x 14"	6"	7"	13"	109	$376.30	$428.90
B-1210 Series - 12" Thickness
B1210-14	12" x 10" x 14"	6"	10"	16"	76	$241.42	$271.32
B1210-24	12" x 10" x 24"	6"	20"	26"	120	$321.02	$350.92
B1210-36-A3*	12" x 10" x 36"	6"	32"	38"	195	$445.37	$492.87
B11210-11	12" x 20" x 11"	6"	7"	13"	134	$404.64	$463.44

*Center anchorage device A-3 is recommended for 36" long bumpers, and is included in the price. A-3 will be supplied unless
otherwise specified.

NOTE: All mounting holes correspond to standard 4 1/2" and 6" thick units.

1/4" Flat plates may be substituted for one or both angles.

8" Thickness now available at same price as B910 Series




1.	Determine (measure) your inclined driveway to establish the amount of driveway rise and your driveway length. See sketch below.

	"A" Note: In cases where the building wall is setback from the edge of the dock, the actual bumper projection required is less the building setback. Example: The incline chart indicates a 12" bumper "A" dimension but the building wall is setback 3", therefore the actual bumper necessary would be 9".

2.	Determine the required dock bumper thickness (projection) by using the incline chart below. This chart is designed to leave the top of the truck approximately either 2" or 6" from the building wall when the truck is fully docked. If your building does not have dock seals installed then the 2" minimum top clearance (C dimension) can be used to select the bumper projection. However, if dock seals are installed, it is recommended that a 6" top clearance be used (C dimension) in order to avoid damage to both building and dock seal.

	a.	Find your driveway rise in the left column and follow across the chart to a driveway length closest to your actual measured length. Dimensions in columns C = 2 and C = 6 are the actual calculated thickness of your dock bumpers.


		The corresponding bumper series are listed in the adjacent columns. Using either the C = 2" or C = 6" top clearance series, select your actual dock bumpers from price table A above.

	b.	Example: Driveway rise is 18", driveway length is 40'. At the intersection of these two rows in the chart, the C = 2 (2" clearance) calculated bumper projection is 6.28" and the suggested dock bumper series is the B610 series.


		Refer back to price table A to select the particular B610 series dock bumper length (C) desired and the corresponding model #.

NOTE: Due to the extensive width of the following chart, it had to be split into two sections (10' - 40' and 50' - 70').

10'

20'

30'

40'

Rise

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52

3.90	B4510-	7.90	B910-
5.80	B610-	9.80	B10510-
7.70	B910-	11.70	B1210-
9.60	B10510-	13.60
11.50	B1210-	15.50
13.40		17.40
15.30		19.30
17.20		21.20
19.10		23.10
21.00		25.00
22.90		26.90
24.80		28.80
26.70		30.70
28.60		32.60
30.50		34.50
32.40		36.40
34.30		38.30
36.20		40.20
38.10		42.10
40.00		44.00
41.90		45.90
43.80		47.80
45.70		49.70
47.60		51.60
49.50		53.50
51.40		55.40

2.95	B4510-	6.95	B910-
3.90	B4510-	7.90	B910-
4.85	B610-	8.85	B910-
5.80	B610-	9.80	B10510-
6.75	B910-	10.75	B1210-
7.70	B910-	11.70	B1210-
8.65	B910-	12.65	B1210-
9.60	B10510	13.60
10.55	B1210	14.55
11.50	B1210	15.50
12.45	B1210	16.45
13.40		17.40
14.35		18.35
15.30		19.30
16.25		20.25
17.20		21.20
18.15		22.15
19.10		23.10
20.05		24.05
21.00		25.00
21.95		25.95
22.90		26.90
23.85		27.85
24.80		28.80
25.75		29.75
26.70		30.70

2.63	B4510-	6.63	B610-
3.27	B4510-	7.27	B910-
3.90	B4510-	7.90	B910-
4.53	B4510-	8.53	B910-
5.17	B610-	9.17	B910-
5.80	B610-	9.80	B10510
6.43	B610-	10.43	B10510
7.07	B910-	11.07	B1210-
7.70	B910-	11.70	B1210-
8.33	B910-	12.33	B1210-
8.97	B910-	12.97
9.60	B10510-	13.60
10.23	B10510-	14.23
10.87	B1210-	14.87
11.50	B1210-	15.50
12.13	B1210-	16.13
12.77		16.77
13.40		17.40
14.03		18.03
14.67		18.67
15.30		19.30
15.93		19.93
16.57		20.57
17.20		21.20
17.83		21.83
18.47		22.47

2.48	B4510-	6.48	B910-
2.95	B4510-	6.95	B910-
3.43	B4510-	7.43	B910-
3.90	B4510-	7.90	B910-
4.38	B4510-	8.38	B910-
4.85	B610-	8.85	B910-
5.33	B610-	9.33	B10510-
5.80	B610-	9.80	B10510-
6.28	B610-	10.28	B10510-
6.75	B910-	10.75	B1210-
7.23	B910-	11.23	B1210-
7.70	B910-	11.70	B1210-
8.18	B910-	12.18	B1210-
8.65	B910-	12.65	B1210-
9.13	B910-	13.13
9.60	B10510-	13.60
10.08	B10510-	14.08
10.55	B10510-	14.55
11.03	B1210-	15.03
11.50	B1210-	15.50
11.98	B1210-	15.98
12.45	B1210-	16.45
12.93		16.93
13.40		17.40
13.88		17.88
14.35		18.35

50'

60'

70'

Rise

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

Proj.
for
C=2

For
C=2
Use

Proj.
for
C=6

For
C=6
Use

2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52

2.38	B4510-	6.38	B910-
2.76	B4510-	6.76	B910-
3.14	B4510-	7.14	B910-
3.52	B4510-	7.52	B910-
3.90	B4510-	7.90	B910-
4.28	B4510-	8.28	B910-
4.66	B4510-	8.66	B910-
5.04	B4510-	9.04	B910-
5.42	B610-	9.42	B910-
5.80	B610-	9.80	B10510-
6.18	B610-	10.18	B10510-
6.56	B910-	10.56	B1210-
6.94	B910-	10.94	B1210-
7.32	B910-	11.32	B1210-
7.70	B910-	11.70	B1210-
8.08	B910-	12.08	B1210-
8.46	B910-	12.46	B1210-
8.84	B910-	12.84
9.22	B910-	13.22
9.60	B10510-	13.60
9.98	B10510-	13.98
10.36	B10510-	14.36
10.74	B10510-	14.74
11.12	B1210-	15.12
11.50	B1210-	15.50
11.88	B1210-	15.88

2.32	B4510-	6.32	B910-
2.63	B4510-	6.63	B910-
2.95	B4510-	6.95	B910-
3.27	B4510-	7.27	B910-
3.58	B4510-	7.58	B910-
3.90	B4510-	7.90	B910-
4.22	B4510-	8.22	B910-
4.53	B4510-	8.53	B910-
4.85	B610-	8.85	B910-
5.17	B610-	9.17	B910-
5.48	B610-	9.48	B910-
5.80	B610-	9.80	B10510-
6.12	B610-	10.12	B10510-
6.43	B610-	10.43	B10510-
6.75	B910-	10.75	B1210
7.07	B910-	11.07	B1210
7.38	B910-	11.38	B1210
7.70	B910-	11.70	B1210
8.02	B910-	12.02	B1210
8.33	B910-	12.33	B1210
8.65	B910-	12.65
8.97	B910-	12.97
9.28	B910-	13.28
9.60	B10510-	13.60
9.92	B10510-	13.92
10.23	B10510-	14.23

2.27	B4510-	6.27	B910-
2.54	B4510-	6.54	B910-
2.81	B4510-	6.81	B910-
3.09	B4510-	7.09	B910-
3.36	B4510-	7.36	B910-
3.63	B4510-	7.63	B910-
3.90	B4510-	7.90	B910-
4.17	B4510-	8.17	B910-
4.44	B4510-	8.44	B910-
4.71	B4510-	8.71	B910-
4.99	B610-	8.99	B910-
5.26	B610-	9.26	B910-
5.53	B610-	9.53	B10510-
5.80	B610-	9.80	B10510-
6.07	B610-	10.07	B10510-
6.34	B610-	10.34	B10510-
6.61	B910-	10.61	B10510-
6.89	B910-	10.89	B1210-
7.16	B910-	11.16	B1210-
7.43	B910-	11.43	B1210-
7.70	B910-	11.70	B1210-
7.97	B910-	11.97	B1210-
8.24	B910-	12.24
8.51	B910-	12.51
8.79	B910-	12.79
9.06	B910-	13.06

Special Order Products - Contact US

ARCHITECTURAL SPECIFICATIONS - Laminated Rubber Dock Bumpers

		Furnish and install rubber dock bumpers as manufactured by Bondor Division of FS Industries, Providence, RI Model No(s)______________. Resilient rubber material of bumpers shall be rubberized-fabric truck tires cut to uniform size pads and punched to receive 3/4" (19.1 mm) supporting rods.
	•


		All bumpers must be ___________________ thick (projection from dock), and closed with two 3" x 3" x 1/4" (76.2 mm x 76.2 mm x 6.35 mm) structural angles under approximately 1,500 pounds (680.4 kg) of pressure. The angles are welded to 3/4" (19.1 mm) rods at one end and closed with threaded rod and nut at the other end.
	•


		The anchor leg of angle extends a minimum of 3" (76.2 mm) beyond the rubber surface at either end and contains two or three 13/16" (20.6 mm) anchor bolt holes as required. (Anchor bolts are supplied separately.)
	•
	•

		The finish for exposed metal parts shall be either chrome aluminum lead-free enamel, hot-dipped galvanized.

Dock Bumper, Dock Bumpers, Laminated Dock Bumper, Laminated Dock Bumpers, Loading Dock Bumper, Loading Dock Bumpers,
Rubber Dock Bumper, Rubber Dock Bumpers, Truck Dock Bumper, Truck Dock Bumpers, and Laminated Rubber Bumpers from your
complete source for material handling equipment.